Licensed & insured · NC electrical contractor
Mon–Fri 8AM–5PM · Emergency 24/7
Licensed & insured · NC electrical contractor
Mon–Fri 8AM–5PM · Emergency 24/7
East Point Electric handles panel upgrades Erwin NC homeowners can trust: a load calculation first, a new panel sized for how you live now, a pulled permit, utility coordination and a Harnett County inspection. One written price, no hourly meter.
Many Erwin homes were wired when a house ran a few lights, a refrigerator and a window unit. Today the same service feeds a heat pump, a water heater, a range, a dryer, computers and often an EV charger or a hot tub. A panel sized for a different era cannot keep up, and it shows up as tripping breakers, dimming lights and warm breakers.
Our panel upgrades Erwin NC service replaces the panel, and the meter base and service cable where needed, with equipment sized for the load you actually have. Boris and JB, the two owners, quote the job, pull the permit, coordinate the power shutoff and do the work themselves.
Every one of the panel upgrades Erwin NC homeowners book with us starts the same way: a load calculation, so you buy the service size the house needs, not a guess.
If you recognize two or more of these, it is time to have the panel looked at before you add anything new.
A breaker that trips under normal use is telling you the circuit or the service is overloaded.
Lights that dip when the heat pump or dryer starts point to a service that is short of capacity.
Heat damage on breakers, the bus or wiring is a fire risk. Turn the circuit off and call us.
A full panel with tandem breakers squeezed in has run out of room for the next appliance or addition.
Humidity and water entry corrode breakers and bus bars. Corrosion means poor connections and heat.
Fuse boxes, Federal Pacific, Zinsco and some older panels are routinely flagged by insurers and home inspectors.
Adding an EV charger, a hot tub, a workshop or an addition? Ask about panel upgrades Erwin NC homeowners usually pair with those projects, before the new load goes in.
Some panels are not just old. They have known problems, and these are the panel upgrades Erwin NC insurers and home inspectors most often ask for.
Common in homes built from the 1950s to the 1980s. Stab-Lok breakers have a long record of failing to trip during an overload or short, which is the one job a breaker has.
Breakers can overheat and fuse to the bus bar, so they stay on when they should shut off. Many insurers ask for replacement before renewing a policy.
Fuse boxes are usually 60 amps or less, have no room for modern circuits, and invite oversized fuses. Most lenders and insurers want them gone.
If you are not sure what you have, send us a photo of the panel label when you call about panel upgrades Erwin NC homes like yours need. We can usually tell you what it is before the visit.
Service size is the total power your home can draw at once. Many older Erwin homes have 60 or 100-amp service. Most new homes are built with 200 amps.
We do not guess on panel upgrades Erwin NC homeowners trust us with. A load calculation based on the National Electrical Code totals every appliance in the house and tells us what the service must carry. That number decides the panel.
Planning an EV? Our EV charger installation in Erwin page explains when a load management device can avoid a service upgrade altogether.
Not every panel problem needs a new panel. Part of every panel upgrades Erwin NC assessment is telling you honestly which one you have.
A single failed breaker, a loose neutral, a double-tapped breaker or a missing knockout cover can usually be fixed in one visit without replacing the panel. If the panel is a sound brand, has spare capacity and shows no heat or corrosion damage, a repair is the right call and we will say so.
Fuse boxes, Federal Pacific and Zinsco panels, heat or water damage on the bus, a panel with no room left, or a service that the load calculation shows is too small. In these cases, repairs only delay the job, and panel upgrades Erwin NC homeowners make now cost less than an emergency replacement later.
The price of panel upgrades Erwin NC homeowners pay depends mostly on the service size and whether the meter base, mast and service cable also need replacing. These ranges reflect what licensed contractors across the region publish for 2026. Your quote is a fixed written figure.
| Type of job | Typical installed price | What it usually includes |
|---|---|---|
| Panel replacement, same amperage | $1,200 to $2,200 | New panel and breakers, reconnection of circuits, labeling, permit |
| 100 amp to 200 amp service upgrade | $1,800 to $3,500 | 200A panel, new service conductors, grounding and bonding, permit |
| Upgrade with new meter base, mast and service cable | $3,500 to $5,500+ | Full service entrance replacement, utility coordination |
| Fuse box replacement | $1,500 to $3,500 | Fuse box removal, new breaker panel, AFCI and GFCI where required |
| Subpanel for garage, shop or addition | $500 to $1,500 | Subpanel, feeder, breaker, grounding |
| Whole-home surge protector (with panel) | $350 to $750 | Panel-mounted Type 2 surge device |
| Harnett County permit | About $100 to $300 | Passed through at cost |
Most panel upgrades Erwin NC homeowners book, a 100 to 200 amp upgrade without moving the panel, land between $1,800 and $3,500.
Mention our $150 off a panel upgrade offer when you call (910) 705-6411 and we will apply it to your written quote. One offer per job.
We tell you the exact figure in writing after the site visit, and nothing starts until you approve it.
Every one of our panel upgrades Erwin NC jobs is permitted. Erwin sits inside Harnett County, and the county's inspections department handles electrical inspections for the Town of Erwin. We pull the permit as the licensed contractor, schedule the inspection and are on site when the inspector arrives.
A service upgrade also needs the power company. Depending on your address, that is Duke Energy or South River EMC. We arrange the disconnect and reconnect at the meter, so the house is without power for the working day only, not overnight.
The inspection record protects your insurance claim, satisfies lenders and home inspectors, and follows the house to closing.
One price covers the full job, not just the box on the wall.
A new panel from a major brand with copper bus, new breakers, and AFCI and GFCI protection where current code requires it.
New service conductors, grounding electrodes and bonding, plus the meter base and mast when they are part of the scope.
Permit, inspection, a typed circuit directory inside the door, and the records you need for your insurer or lender.
Many homeowners add whole-home surge protection during the upgrade, since it mounts at the panel and storm surges are common here in summer.
The installation itself is usually one day. Permits and utility scheduling set the overall calendar, typically one to three weeks.
We inspect the panel, meter base, mast and grounding, and total your existing and planned loads.
One figure in writing, with service size, meter base work and options like surge protection listed separately.
We file with Harnett County and book the disconnect and reconnect with your power company.
Most panel upgrades Erwin NC homes need are finished in one working day. Power is off from the morning disconnect until reconnect.
The county inspector signs off the new service. We are on site for it.
We test every circuit, label the directory and show you the main breaker and any new protection devices.
Erwin grew up around the Erwin Cotton Mill, and the age of the house shapes every panel job.
Houses built for mill workers were wired for a few lamps and a radio. Panel upgrades Erwin NC homeowners need in these houses often include fuse box removal, new grounding and some branch circuit repair.
This is where Federal Pacific, Zinsco and full 100-amp panels show up most. Heat pumps and electric ranges have usually outgrown them.
200-amp service is standard, but EV chargers, generators and finished bonus rooms can still fill the panel. A subpanel or load device often solves it.
NC electrical contractor license 38759, with liability and workers' compensation cover. A certificate of insurance is sent before work starts.
On all panel upgrades Erwin NC homeowners request, the load calculation decides the service size. You never pay for more than the house needs.
We price the job, not the hour. The figure you approve is the figure you pay.
Boris and JB run every job. No call center and no subcontracted crews.
We file, schedule and meet the Harnett County inspector on all panel upgrades Erwin NC homes receive from us.
Erwin is one of our main service locations, so we are close enough to come back quickly if you ever need us.
Two quotes for panel upgrades Erwin NC homeowners receive can look far apart until you line up what each one actually includes. Ask these six questions of every quote.
Panel upgrades Erwin NC jobs need a Harnett County electrical permit. A quote that leaves it out is cheaper on paper and leaves you without the inspection record.
If the meter base or mast is rusted or undersized, it has to be replaced with the panel. A good quote says whether that is included or priced separately.
The size of the new service should come from what the house actually draws, not a guess. Ask to see the numbers behind 150 or 200 amps.
Current code calls for AFCI and GFCI protection in many locations. Those breakers cost more and should be listed, not assumed.
Someone has to schedule the disconnect and reconnect with Duke Energy or South River EMC. It should be the electrician, and it should be in the scope.
With the panel open, a whole-home surge device costs far less to add. Ask for it as a separate line so you can decide.
Many panel upgrades Erwin NC homeowners book start with a purchase: a heat pump, an EV, a hot tub or a shop. Checking capacity first avoids buying equipment the panel cannot carry.
A new heat pump with electric backup heat can be the largest load in the house. We check the service before the HVAC contractor sizes the unit.
A Level 2 charger needs a dedicated 40 to 50 amp circuit. On a 100-amp service that often means panel upgrades Erwin NC drivers did not plan for, or a load management device.
These need their own circuits and sometimes a subpanel. Planning them with the panel upgrade avoids paying twice.
Most panel upgrades erwin nc jobs follow the same path. Knowing it up front helps you plan around work, school and the Harnett County inspection schedule.
You tell us what you want and where the panel is. For panel upgrades erwin nc work we ask about the age of the house, the panel brand and anything that has been tripping, so the first visit has the right parts on the truck.
We look at the panel, the wiring route and the location, run a load calculation where capacity matters, and give you an itemised price in writing. Nothing starts until you approve it.
Permitted panel upgrades erwin nc work is filed with Harnett County, completed to current NEC code, and inspected. We meet the inspector, label the panel and leave you the permit record for your insurer or a future buyer.
Along with panel upgrades Erwin NC homeowners book, we upgrade panels across sixteen cities in Cumberland, Harnett, Lee, Wake, Sampson, Bladen and Hoke counties. See our main electrical panel upgrade page for more detail, or our lighting installation and ceiling fan installation pages for Erwin.
A same-size panel replacement usually costs $1,200 to $2,200. A 100 to 200 amp upgrade typically runs $1,800 to $3,500, and jobs that include a new meter base, mast and service cable can reach $3,500 to $5,500 or more.
The installation is usually one working day. Permits, utility scheduling and inspection mean the full project typically takes one to three weeks from approval.
Yes, for most of the working day. The power company disconnects at the meter in the morning and reconnects once the new service is ready.
Yes. Panel and service changes are permitted work through Harnett County, which handles inspections for the Town of Erwin. We pull the permit and meet the inspector.
A load calculation decides. All-electric homes and homes adding an EV charger, hot tub or shop usually need 200 amps. Smaller homes with gas heat may be fine at 100 amps.
Yes. Both have known breaker problems, and many insurers and home inspectors flag them. Replacement is the fix.
If the main service has enough capacity and you only need more breaker space, a subpanel can be the cheaper answer. The load calculation tells us which option fits.
Not always. Many 200-amp homes have room. If yours does not, a load management device or lower-amperage charger may avoid the upgrade.
Call (910) 705-6411 and tell us what is tripping, what panel you have and what you plan to add. We will run the load calculation, price it in writing and handle the permit and the power company. For panel upgrades Erwin NC homeowners can rely on, call East Point Electric.